Most cellular Internet of Things (IoT) sensors are installed in the parts of a building people rarely visit: plant rooms, basements, ceiling cavities, risers and cold stores. Those are also the parts of a building where mobile signal is weakest. When an IoT sensor can’t hold a connection, the data it was installed to collect stops arriving, and often nobody notices until someone goes looking for a reading.
Low-power cellular technologies like LTE-M (Long Term Evolution for Machines) and NB-IoT (Narrowband Internet of Things) were designed to reach further indoors than standard 4G. They do, up to a point. Concrete, steel and below-ground locations can still push a device past what the network can reach.
This article covers how cellular IoT sensors connect, why they lose connection inside buildings, and how in-building coverage (IBC) systems keep them online.
IoT sensors measure a physical condition and report it over a network. In commercial buildings, the main uses typically include:
Not every IoT sensor uses the mobile network. Many run on Wi-Fi, Zigbee or LoRaWAN (Long Range Wide Area Network) and report through a local gateway. Cellular IoT sensors connect straight to a carrier network using a SIM, so there’s no local network to install or maintain. That makes cellular popular for spread-out sites and hard-to-wire locations, and it’s why indoor mobile coverage decides whether these devices work.
Gateways matter too. Plenty of LoRaWAN and Zigbee gateways send their data out over 4G, so even a non-cellular sensor network can depend on a mobile signal where the gateway is mounted.
LTE-M and NB-IoT both run inside existing 4G networks. In Australia, Telstra’s IoT network carries both, including on its 700MHz band.
Their advantage indoors is extra reach. NB-IoT can hold a connection through roughly 20 decibels (dB) more signal loss than standard 4G, which is enough to get through an extra wall or floor in many buildings.
The trade-off is in how they do it. A device in poor coverage repeats each transmission many times until the network receives it, and every repetition uses battery. A sensor rated for years of battery life in good coverage can need a replacement much sooner when it sits at the edge of the network.
That extra reach has a limit, and commercial buildings test it. The most common causes of dropouts include:
Recommended Read: No Signal in the Basement? How In-Building Coverage Systems Fix Underground Blackspots
A sensor that can’t connect still looks fine on the wall, so the impact usually shows up somewhere else first:
Moving a sensor closer to a window isn’t an option when it needs to sit in a riser or under a chiller. The reliable fix is to bring the mobile signal to the sensors. The right solution depends on the size of the site, where the sensors sit and which carriers their SIMs use.
For a single plant room, basement level or cold store, a CEL-FI signal booster is often the right fit. It captures the available outdoor signal, amplifies it and rebroadcasts it indoors through internal antennas.
CEL-FI models are carrier-specific, so the right unit depends on which network your IoT SIMs use. For Telstra-connected sensors, that means a system covering the 700MHz band.
For multi-level buildings and campuses with sensors spread across many floors, a DAS typically fits better. A DAS uses a network of internal antennas connected to a central system to deliver consistent coverage across the whole site.
A DAS works well for IoT sensors because it:
An in-building system only helps IoT sensors if it carries the frequency bands those sensors use. Every installation in Australia also has to meet Australian Communications and Media Authority (ACMA) requirements and carrier approvals. Non-compliant boosters can interfere with the wider mobile network and expose the building owner to regulatory risk.
IoT sensor connectivity is cheapest to solve before devices go in. The right approach depends on:
A professional site assessment is the starting point. It measures a mobile signal in the exact spots where sensors sit, identifies what’s causing the gaps and confirms which solution will keep every device connected.
MobileCorp is an Australian in-building coverage specialist. We work with commercial building owners, facilities managers and operators across the country to design and deliver multi-carrier IBC systems that keep IoT sensors, staff phones and building systems connected. Every project starts with a site survey conducted by a qualified engineer, and every solution is engineered around the specific building, where its sensors sit and which carriers they rely on. We also provide IoT managed services and machine-to-machine (M2M) connectivity, so the coverage and the devices it supports can be planned together.
Request an Obligation-Free Site Assessment
Cellular IoT sensors do, because they connect directly to a carrier network through a SIM. Sensors on Wi-Fi, Zigbee or LoRaWAN use their own local networks, but many of their gateways send data out over 4G, so the gateway location still needs reliable mobile signal.
NB-IoT reaches further into buildings, which suits stationary, low-data devices like meters and leak sensors. LTE-M handles more data and supports devices that move, such as asset trackers.
Battery life ratings assume good coverage. In weak signal conditions, LTE-M and NB-IoT devices repeat each transmission many times so the network can receive it, and every repetition uses power. A sensor at the edge of coverage can need a new battery years earlier than its rating suggests.
Yes, as long as it’s carrier-approved and covers the frequency bands your IoT SIMs use. A CEL-FI booster suits a single zone like a basement or plant room, while a DAS suits larger buildings. Non-approved boosters are illegal in Australia and can interfere with the mobile network.
A site assessment measures signal strength and quality at each sensor location, including basements, risers and plant rooms. It identifies which spots fall below what your devices need, what’s causing the gaps and which in-building coverage solution will cover them.